Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterTrusted Garage Door Installation for Bellevue Homeowners
A new garage door installation in Bellevue typically runs $700-$2,200 depending on door size, material, and insulation level. Most single-door replacements take one day on site, and you’ll have a written price with a written scope before any work begins. We’ve been making garage doors right in Bellevue since 2015, with 18,000+ installations and repairs completed across the Eastside, and Marcus Deller still holds every job to the same standard he started with: the customer sees the evidence before they spend a dollar. If your door is sagging, dented, rusting at the bottom panels, or you’re tired of the noise every time it cycles, call (425) 696-3561 and we’ll schedule a free measure.
What Our Garage Door Installation Service Includes
Every installation starts with a documented assessment and ends with a photo record of what we found, what we installed, and what we tested. No verbal handshakes, no vague “we’ll take care of it.” Clause 1 of The Haven Standard means the flat, written price and written scope are already in your hands before we unload a single tool.
New Door Installation
A full door replacement makes sense when the panels, tracks, or hardware have reached the point where repairing one component will just expose the next one. We remove the old door, inspect the framing and mounting points, install the new door, and test the full cycle including the opener. Your final record includes photos of the old hardware we removed, the new door mounted, and the balance test we run before we leave.
Single Car Door
Single doors are the most common installation we do in Bellevue, from the 1960s ramblers in Lake Hills to newer townhomes in Spring District. A standard single door is typically 8×7 or 9×7, and we’ll confirm your exact rough opening before quoting anything. If you’re replacing a single door on an attached garage, we’ll also check the opener’s force settings so the new door doesn’t fight an old motor.
Double Car Door
Double doors run 16 feet wide in most Bellevue homes, and that width changes how we approach installation: heavier torsion springs, more panel sections, and closer attention to track alignment. We measure the header, the side clearance, and the backroom depth before recommending a door, because some double-door models need more horizontal track than a shallow garage can give. The written scope will name the spring size and wire diameter we’re spec’ing, so you can see the math rather than trust a guess.
Custom Garage Door
Custom doors are for homeowners who want a specific look, an unusual size, or a door that matches the architectural style of the house rather than the cheapest option at a big-box store. We’ll work from your specs or your inspiration photos, price the door and the hardware separately, and give you a written lead-time before you commit to anything. You’ll know the exact door model, panel profile, color, and window configuration before the order goes in.
Steel Doors
Steel doors are the most popular choice in Bellevue because they hold up to rain and everyday use without the maintenance wood demands. We install insulated and non-insulated steel doors in a range of gauge thicknesses, and we’ll show you the R-value on the spec sheet before you choose. If your current steel door is rusting through at the bottom panel, we’ll photograph the corrosion and show you exactly why replacement beats another patch job.
Wood Doors
Wood doors weigh more than steel, and that means the springs, cables, and tracks have to be spec’d to match, or the door will wear the hardware out early. We install solid wood and wood-composite doors and set the spring balance specifically for the door’s actual weight, not a chart average. Wood doors also need more care in a wet climate like Bellevue’s, and we’ll be straight with you about the sealing and maintenance a wood door will ask for over its life.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Garage Door Installation
We install and service LiftMaster and Chamberlain openers alongside new doors, and we carry their OEM parts on the truck so we aren’t improvising with aftermarket logic boards or limit switches. LiftMaster’s current line has changed its travel-limit setup more than once, and we program the limits and force settings on site so the door reverses correctly before we hand it over.
Craftsman and Raynor doors show up in a lot of Bellevue garages from the 1990s and 2000s, and replacement parts for those older units aren’t always on the shelf at the local hardware store. We keep common Craftsman gears, belts, and safety sensors in stock, and we know which Raynor door models have discontinued panel profiles. Whether you have one of those brands or any other make, we can measure, spec, and install the right replacement.
Before
AfterSigns You Need Garage Door Installation Right Now
- Your door is visibly sagging or leaning when open. This usually means the panels, hinges, or track brackets have lost structural integrity. A sagging door puts stress on the opener and can fail suddenly, which is why we photograph the hardware during the estimate so you can see what’s holding and what isn’t.
- The bottom panel is rusted, cracked, or soft to the touch. In Bellevue’s wet winters, moisture sits at the bottom of the door and works on steel panels from the inside out. Once the bottom panel fails, the door can’t seal properly, and replacing one panel on an older door often costs close to a full replacement once you factor in labor and a mismatched finish.
- You hear grinding, popping, or a loud bang during operation. A single sharp bang is often a torsion spring breaking. Grinding metal usually means rollers or hinges are worn. Either way, a broken door component under tension is dangerous to work around, and we recommend letting a trained technician inspect it rather than operating the door.
- Your door won’t open or close fully, or reverses mid-cycle. This can be a limit switch problem, a track obstruction, or a failing logic board in the opener. If the door is original to the house and the opener was installed before 2010, you’re likely looking at replacing both, not repairing one component.
- The door is dented, warped, or clearly beyond cosmetic repair. Dents in a steel door will eventually compromise the panel’s rigidity, and warped wood doors put uneven load on the springs. When the door’s structure is going, every cycle is wearing out the rest of the system.
Our Garage Door Installation Process - Step by Step
- 1
Measure and document. We confirm the rough opening, header clearance, side room, and backroom, and we photograph the existing door, tracks, springs, and mounting points. This is the record that drives the quote, so you never hear “we didn’t expect that” after the work starts.
- 2
Written price and written scope. Before any work begins, you get a flat price and a line-item scope per Clause 1 of The Haven Standard. It names the door model, material, insulation level, spring spec, and what we’ll do with the old door and hardware.
- 3
Removal and inspection. We remove the old door and inspect the framing, mounting brackets, and opener compatibility. If we find something the old door was hiding, we show you the photo and quote the adjustment before proceeding.
- 4
Installation and balance. We mount the new door, set the torsion springs to the door’s actual weight, align the tracks, and install or reconnect the opener. Then we run a full balance test and a safety reversal test, and we adjust the travel limits on the opener so the door stops where it should.
- 5
Photo record and walkthrough. You receive photos of the old components we removed, the new door installed, and the test results. We walk you through what was done and answer any questions before we leave. That’s Clause 4 in practice: you see the work, not just the invoice.
How Much Does Garage Door Installation Cost in Bellevue?
A standard single-door installation in Bellevue runs $700-$1,400 for a basic non-insulated steel door, while a double door with insulation and windows typically runs $1,400-$2,200. Custom wood doors or oversized openings push higher, and we’ll tell you exactly why before you commit.
The price is driven by door size, material (steel vs. wood), insulation R-value, window options, and whether the existing tracks and opener can be reused. You avoid overpaying by getting a written scope that separates the door cost from the labor and the hardware, so you can see where every dollar goes. You avoid surprises because the price we quote is the price on the invoice: no change-order games, no “we found extra work” after the old door is off.
A free estimate includes the full measurement, the assessment of your existing opener’s compatibility, and a written quote you can compare line by line. If you have a written estimate from another company, bring it: we’ll give you a free second opinion and show you where the pricing differs, no coupon required.
Garage Door Installation Near Bellevue - Our Service Area
We install garage doors throughout Bellevue and the surrounding Eastside, including Newcastle, Redmond, Kirkland, Issaquah, Renton, and Seattle. Most Bellevue installations are scheduled within a few days of the measure, and the installation itself is typically done in a single visit. We answer the phone live, 24/7, so when you call (425) 696-3561 you talk to a person who can schedule the measure.
Serving Bellevue, WA - Our Local Coverage Area
We’re based in the Bellevue area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Garage Door Installation in Bellevue
Garage door installation is the removal of an existing door and the mounting, balancing, and testing of a new door in its place. A full installation includes the door panels, tracks, torsion springs, hinges, rollers, and the connection to your existing or new opener. At Servo, installation always ends with a documented photo record of what was removed, what was installed, and what was tested.
A standard single-door installation takes one day on site, including removal of the old door and full testing of the new one. Custom doors or double-wide openings may take longer, and we’ll give you a written timeline with the quote. You’ll know the schedule before you pay for anything.
A new door installation in Bellevue runs $700-$2,200 depending on size, material, insulation, and window options. A basic single steel door starts around $700, and a fully insulated double door with windows reaches about $2,200. Every quote is a flat, written price delivered before work starts, so you’ll never get a surprise invoice. Call (425) 696-3561 for your exact price, it’s a free estimate.
Yes. We install LiftMaster and Chamberlain openers alongside or separate from a new door, and we carry their OEM parts on the truck. We program the travel limits, force settings, and safety reversal on site, and we test the full cycle before we leave. If your existing opener is compatible with the new door, we’ll tell you and leave it in place rather than selling a replacement you don’t need.
If your door failed suddenly and the structure is unsafe, we can often get a technician to your Bellevue home the same day to assess and secure the opening. Full door installation is typically measured and scheduled, but we answer emergency calls 24/7 and will get you a real person on the phone, not a recording. Call (425) 696-3561 and we’ll tell you straight what’s possible today.
Our installations are covered by the 365-Day Done Right Promise: if the installation isn’t right, we make it right. The manufacturer’s warranty on the door and hardware applies as well, and we’ll give you the warranty paperwork with your photo record at the end of the job. You don’t need a coupon or a code, and the promise is written into The Haven Standard, not a verbal guarantee.
Clear the area inside the garage about six feet back from the door, and move vehicles out of the driveway before we arrive. If you have items stored in the overhead path of the door, move those as well. We handle the removal and disposal of the old door, and we’ll protect the floor and any nearby belongings while we work. If you have a security system sensor on the door, let us know ahead so we can coordinate with your provider.
Schedule Your Garage Door Installation Service in Bellevue Today
You’ll get a flat, written price and a written scope before any work starts, that’s non-negotiable. You’ll also get our phone number answered by a real person, 24/7. Call (425) 696-3561 to schedule your free measure and estimate for garage door installation in Bellevue. We’ll show you the numbers, the scope, and the photos, and then you decide.
Written by Marcus Deller, Owner at Servo Garage Doors Bellevue, serving Bellevue since 2015.